高通msm8909耳机调试

1、DTS相应修改:

DTS相关代码:kernel/arch/arm/boot/dts/qcom/msm8909-qrd-skuc.dtsi:

 1     sound {
 2         compatible = "qcom,msm8x16-audio-codec";
 3         qcom,model = "msm8909-skuc-snd-card";
 4         qcom,msm-snd-card-id = <0>;
 5         qcom,msm-codec-type = "internal";
 6         qcom,msm-ext-pa = "primary";
 7         qcom,msm-mclk-freq = <9600000>;
 8         qcom,msm-mbhc-hphl-swh = <0>;        //高通平台耳机驱动机制为MBHC,hphl为高通耳机平台的设置
 9         qcom,msm-mbhc-gnd-swh = <0>;
10         qcom,msm-hs-micbias-type = "internal";
11         qcom,msm-micbias1-ext-cap;
12         qcom,msm-micbias2-ext-cap;
13         qcom,audio-routing =
14             "RX_BIAS", "MCLK",
15             "SPK_RX_BIAS", "MCLK",
16             "INT_LDO_H", "MCLK",
17             "MIC BIAS Internal1", "Handset Mic",
18             "MIC BIAS Internal2", "Headset Mic",
19             "MIC BIAS Internal3", "Secondary Mic",
20             "AMIC1", "MIC BIAS Internal1",
21             "AMIC2", "MIC BIAS Internal2",
22             "AMIC3", "MIC BIAS Internal3";
23         pinctrl-names = "cdc_lines_act",
24                 "cdc_lines_sus";
25         pinctrl-0 = <&cdc_pdm_lines_act>;
26         pinctrl-1 = <&cdc_pdm_lines_sus>;
27         asoc-platform = <&pcm0>, <&pcm1>, <&voip>, <&voice>,
28                 <&loopback>, <&compress>, <&hostless>,
29                 <&afe>, <&lsm>, <&routing>, <&lpa>,
30                 <&voice_svc>;
31         asoc-platform-names = "msm-pcm-dsp.0", "msm-pcm-dsp.1",
32                 "msm-voip-dsp", "msm-pcm-voice", "msm-pcm-loopback",
33                 "msm-compress-dsp", "msm-pcm-hostless", "msm-pcm-afe",
34                 "msm-lsm-client", "msm-pcm-routing", "msm-pcm-lpa",
35                 "msm-voice-svc";
36         asoc-cpu = <&dai_pri_auxpcm>, <&dai_hdmi>,
37                 <&dai_mi2s0>, <&dai_mi2s1>, <&dai_mi2s2>, <&dai_mi2s3>,
38                 <&sb_0_rx>, <&sb_0_tx>, <&sb_1_rx>, <&sb_1_tx>,
39                 <&sb_3_rx>, <&sb_3_tx>, <&sb_4_rx>, <&sb_4_tx>,
40                 <&bt_sco_rx>, <&bt_sco_tx>, <&int_fm_rx>, <&int_fm_tx>,
41                 <&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>, <&afe_proxy_tx>,
42                 <&incall_record_rx>, <&incall_record_tx>, <&incall_music_rx>,
43                 <&incall_music_2_rx>;
44         asoc-cpu-names = "msm-dai-q6-auxpcm.1", "msm-dai-q6-hdmi.8",
45                 "msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
46                 "msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
47                 "msm-dai-q6-dev.16384", "msm-dai-q6-dev.16385",
48                 "msm-dai-q6-dev.16386", "msm-dai-q6-dev.16387",
49                 "msm-dai-q6-dev.16390", "msm-dai-q6-dev.16391",
50                 "msm-dai-q6-dev.16392", "msm-dai-q6-dev.16393",
51                 "msm-dai-q6-dev.12288", "msm-dai-q6-dev.12289",
52                 "msm-dai-q6-dev.12292", "msm-dai-q6-dev.12293",
53                 "msm-dai-q6-dev.224", "msm-dai-q6-dev.225",
54                 "msm-dai-q6-dev.241", "msm-dai-q6-dev.240",
55                 "msm-dai-q6-dev.32771", "msm-dai-q6-dev.32772",
56                 "msm-dai-q6-dev.32773", "msm-dai-q6-dev.32770";
57         asoc-codec = <&stub_codec>, <&pm8909_conga_dig>;      //在这里使用了pm8909电源管理芯片的codec芯片
58         asoc-codec-names = "msm-stub-codec.1", "tombak_codec";
59     };

通过find ./ -name "*8909*" | xargs grep -n "pm8909_conga_dig"来搜索关键字:

kernel/arch/arm/boot/dts/qcom/msm-pm8909.dtsi:

    pm8909_conga_dig: 8909_wcd_codec@f000 {
            compatible = "qcom,msm8x16_wcd_codec";
            reg = <0xf000 0x100>;
            interrupt-parent = <&spmi_bus>;
            interrupts = <0x1 0xf0 0x0>,
                     <0x1 0xf0 0x1>,
                     <0x1 0xf0 0x2>,
                     <0x1 0xf0 0x3>,
                     <0x1 0xf0 0x4>,
                     <0x1 0xf0 0x5>,
                     <0x1 0xf0 0x6>,
                     <0x1 0xf0 0x7>;
            interrupt-names = "spk_cnp_int",
                      "spk_clip_int",
                      "spk_ocp_int",
                      "ins_rem_det1",
                      "but_rel_det",
                      "but_press_det",
                      "ins_rem_det",
                      "mbhc_int";

            cdc-vdda-cp-supply = <&pm8909_s2>;
            qcom,cdc-vdda-cp-voltage = <1800000 2200000>;
            qcom,cdc-vdda-cp-current = <500000>;

            cdc-vdda-h-supply = <&pm8909_l5>;
            qcom,cdc-vdda-h-voltage = <1800000 1800000>;
            qcom,cdc-vdda-h-current = <10000>;

            cdc-vdd-px-supply = <&pm8909_l5>;
            qcom,cdc-vdd-px-voltage = <1800000 1800000>;
            qcom,cdc-vdd-px-current = <5000>;

            cdc-vdd-pa-supply = <&pm8909_s2>;
            qcom,cdc-vdd-pa-voltage = <1800000 2200000>;
            qcom,cdc-vdd-pa-current = <260000>;

            cdc-vdd-mic-bias-supply = <&pm8909_l13>;
            qcom,cdc-vdd-mic-bias-voltage = <3075000 3075000>;
            qcom,cdc-vdd-mic-bias-current = <5000>;

            qcom,cdc-mclk-clk-rate = <9600000>;

            qcom,cdc-static-supplies = "cdc-vdda-h",
                           "cdc-vdd-px",
                           "cdc-vdd-pa",
                           "cdc-vdda-cp";

            qcom,cdc-on-demand-supplies = "cdc-vdd-mic-bias";
        };

        pm8909_conga_analog: 8909_wcd_codec@f100 {
            compatible = "qcom,msm8x16_wcd_codec";
            reg = <0xf100 0x100>;
            interrupt-parent = <&spmi_bus>;
            interrupts = <0x1 0xf1 0x0>,
                     <0x1 0xf1 0x1>,
                     <0x1 0xf1 0x2>,
                     <0x1 0xf1 0x3>,
                     <0x1 0xf1 0x4>,
                     <0x1 0xf1 0x5>;
            interrupt-names = "ear_ocp_int",
                      "hphr_ocp_int",
                      "hphl_ocp_det",
                      "ear_cnp_int",
                      "hphr_cnp_int",
                      "hphl_cnp_int";
        };

msm8909的耳机接口在pm8909上,耳机检测脚是HS_DET。

确定自己的插座是NO还是NC的,详情查看博客:http://www.cnblogs.com/linhaostudy/p/8260813.html

通过检查,判断JACK为NO状态;根据高通bring up 手册更改相应的DTSI:

1 qcom,msm-mbhc-hphl-swh = <1>;    //由0改为1

2、kernel分析:

kernel/sound/soc/codecs/msm8x16-wcd.c

1 static const struct wcd_mbhc_intr intr_ids = {
2     .mbhc_sw_intr =  MSM8X16_WCD_IRQ_MBHC_HS_DET,
3     .mbhc_btn_press_intr = MSM8X16_WCD_IRQ_MBHC_PRESS,
4     .mbhc_btn_release_intr = MSM8X16_WCD_IRQ_MBHC_RELEASE,
5     .mbhc_hs_ins_intr = MSM8X16_WCD_IRQ_MBHC_INSREM_DET1,
6     .mbhc_hs_rem_intr = MSM8X16_WCD_IRQ_MBHC_INSREM_DET,
7     .hph_left_ocp = MSM8X16_WCD_IRQ_HPHL_OCP,
8     .hph_right_ocp = MSM8X16_WCD_IRQ_HPHR_OCP,
9 };

  这个结构体描述了msm8909的wcdx系列的codec芯片的MBHC的信息;

  1 static int msm8x16_wcd_codec_probe(struct snd_soc_codec *codec)
  2 {
  3     struct msm8x16_wcd_priv *msm8x16_wcd_priv;
  4     struct msm8x16_wcd *msm8x16_wcd;
  5     int i, ret;
  6 
  7     dev_dbg(codec->dev, "%s()\n", __func__);
  8 
  9     msm8x16_wcd_priv = kzalloc(sizeof(struct msm8x16_wcd_priv), GFP_KERNEL);
 10     if (!msm8x16_wcd_priv) {
 11         dev_err(codec->dev, "Failed to allocate private data\n");
 12         return -ENOMEM;
 13     }
 14 
 15     for (i = 0; i < NUM_DECIMATORS; i++) {
 16         tx_hpf_work[i].msm8x16_wcd = msm8x16_wcd_priv;
 17         tx_hpf_work[i].decimator = i + 1;
 18         INIT_DELAYED_WORK(&tx_hpf_work[i].dwork,
 19             tx_hpf_corner_freq_callback);
 20     }
 21 
 22     codec->control_data = dev_get_drvdata(codec->dev);
 23     snd_soc_codec_set_drvdata(codec, msm8x16_wcd_priv);
 24     msm8x16_wcd_priv->codec = codec;
 25 
 26     /* codec resmgr module init */
 27     msm8x16_wcd = codec->control_data;
 28     msm8x16_wcd->dig_base = ioremap(MSM8X16_DIGITAL_CODEC_BASE_ADDR,
 29                   MSM8X16_DIGITAL_CODEC_REG_SIZE);
 30     if (msm8x16_wcd->dig_base == NULL) {
 31         dev_err(codec->dev, "%s ioremap failed\n", __func__);
 32         kfree(msm8x16_wcd_priv);
 33         return -ENOMEM;
 34     }
 35     msm8x16_wcd_priv->spkdrv_reg =
 36         wcd8x16_wcd_codec_find_regulator(codec->control_data,
 37                         MSM89XX_VDD_SPKDRV_NAME);
 38     msm8x16_wcd_priv->pmic_rev = snd_soc_read(codec,
 39                     MSM8X16_WCD_A_DIGITAL_REVISION1);
 40     msm8x16_wcd_priv->codec_version = snd_soc_read(codec,
 41                     MSM8X16_WCD_A_DIGITAL_PERPH_SUBTYPE);
 42     if (msm8x16_wcd_priv->codec_version == CONGA) {
 43         dev_dbg(codec->dev, "%s :Conga REV: %d\n", __func__,
 44                     msm8x16_wcd_priv->codec_version);
 45         msm8x16_wcd_priv->ext_spk_boost_set = true;
 46     } else {
 47         dev_dbg(codec->dev, "%s :PMIC REV: %d\n", __func__,
 48                     msm8x16_wcd_priv->pmic_rev);
 49     }
 50     /*
 51      * set to default boost option BOOST_SWITCH, user mixer path can change
 52      * it to BOOST_ALWAYS or BOOST_BYPASS based on solution chosen.
 53      */
 54     msm8x16_wcd_priv->boost_option = BOOST_SWITCH;
 55     msm8x16_wcd_dt_parse_boost_info(codec);    //
 56     msm8x16_wcd_set_boost_v(codec);
 57 
 58     snd_soc_add_codec_controls(codec, impedance_detect_controls,
 59                    ARRAY_SIZE(impedance_detect_controls));
 60 
 61     msm8x16_wcd_bringup(codec);
 62     msm8x16_wcd_codec_init_reg(codec);
 63     msm8x16_wcd_update_reg_defaults(codec);
 64 
 65     wcd9xxx_spmi_set_codec(codec);
 66 
 67     msm8x16_wcd_priv->on_demand_list[ON_DEMAND_MICBIAS].supply =
 68                 wcd8x16_wcd_codec_find_regulator(
 69                 codec->control_data,
 70                 on_demand_supply_name[ON_DEMAND_MICBIAS]);
 71     atomic_set(&msm8x16_wcd_priv->on_demand_list[ON_DEMAND_MICBIAS].ref, 0);
 72 
 73     BLOCKING_INIT_NOTIFIER_HEAD(&msm8x16_wcd_priv->notifier);
 74 
 75     msm8x16_wcd_priv->fw_data = kzalloc(sizeof(*(msm8x16_wcd_priv->fw_data))
 76             , GFP_KERNEL);
 77     if (!msm8x16_wcd_priv->fw_data) {
 78         dev_err(codec->dev, "Failed to allocate fw_data\n");
 79         iounmap(msm8x16_wcd->dig_base);
 80         kfree(msm8x16_wcd_priv);
 81         return -ENOMEM;
 82     }
 83 
 84     set_bit(WCD9XXX_MBHC_CAL, msm8x16_wcd_priv->fw_data->cal_bit);
 85     ret = wcd_cal_create_hwdep(msm8x16_wcd_priv->fw_data,
 86             WCD9XXX_CODEC_HWDEP_NODE, codec);
 87     if (ret < 0) {
 88         dev_err(codec->dev, "%s hwdep failed %d\n", __func__, ret);
 89         iounmap(msm8x16_wcd->dig_base);
 90         kfree(msm8x16_wcd_priv->fw_data);
 91         kfree(msm8x16_wcd_priv);
 92         return ret;
 93     }
 94 
 95     wcd_mbhc_init(&msm8x16_wcd_priv->mbhc, codec, &mbhc_cb, &intr_ids,
 96             true);        //在这里获取到了相应的设备树信息
 97 
 98     msm8x16_wcd_priv->mclk_enabled = false;
 99     msm8x16_wcd_priv->clock_active = false;
100     msm8x16_wcd_priv->config_mode_active = false;
101 
102     /* Set initial MICBIAS voltage level */
103     msm8x16_wcd_set_micb_v(codec);
104 
105     /* Set initial cap mode */
106     msm8x16_wcd_configure_cap(codec, false, false);
107     registered_codec = codec;
108     modem_state_notifier =
109         subsys_notif_register_notifier("modem",
110                        &modem_state_notifier_block);
111     if (!modem_state_notifier) {
112         dev_err(codec->dev, "Failed to register modem state notifier\n"
113             );
114         iounmap(msm8x16_wcd->dig_base);
115         kfree(msm8x16_wcd_priv->fw_data);
116         kfree(msm8x16_wcd_priv);
117         registered_codec = NULL;
118         return -ENOMEM;
119     }
120     return 0;
121 }

kernel/sound/soc/codecs/wcd-mbhc-v2.c:

  1 int wcd_mbhc_init(struct wcd_mbhc *mbhc, struct snd_soc_codec *codec,
  2               const struct wcd_mbhc_cb *mbhc_cb,
  3               const struct wcd_mbhc_intr *mbhc_cdc_intr_ids,
  4               bool impedance_det_en)
  5 {
  6     int ret = 0;
  7     int hph_swh = 0;
  8     int gnd_swh = 0;
  9     struct snd_soc_card *card = codec->card;
 10     const char *hph_switch = "qcom,msm-mbhc-hphl-swh";
 11     const char *gnd_switch = "qcom,msm-mbhc-gnd-swh";
 12     const char *ext1_cap = "qcom,msm-micbias1-ext-cap";
 13     const char *ext2_cap = "qcom,msm-micbias2-ext-cap";
 14 
 15     pr_debug("%s: enter\n", __func__);
 16 
 17     ret = of_property_read_u32(card->dev->of_node, hph_switch, &hph_swh);    //在这里找到设备树信息,通过高低电平判断no或者nc的jack
 18     if (ret) {
 19         dev_err(card->dev,
 20             "%s: missing %s in dt node\n", __func__, hph_switch);
 21         goto err;
 22     }
 23 
 24     ret = of_property_read_u32(card->dev->of_node, gnd_switch, &gnd_swh);
 25     if (ret) {
 26         dev_err(card->dev,
 27             "%s: missing %s in dt node\n", __func__, gnd_switch);
 28         goto err;
 29     }
 30     mbhc->micbias1_cap_mode =
 31         (of_property_read_bool(card->dev->of_node, ext1_cap) ?
 32         MICBIAS_EXT_BYP_CAP : MICBIAS_NO_EXT_BYP_CAP);
 33 
 34     mbhc->micbias2_cap_mode =
 35         (of_property_read_bool(card->dev->of_node, ext2_cap) ?
 36         MICBIAS_EXT_BYP_CAP : MICBIAS_NO_EXT_BYP_CAP);
 37 
 38     mbhc->in_swch_irq_handler = false;
 39     mbhc->current_plug = MBHC_PLUG_TYPE_NONE;
 40     mbhc->is_btn_press = false;
 41     mbhc->codec = codec;
 42     mbhc->intr_ids = mbhc_cdc_intr_ids;
 43     mbhc->impedance_detect = impedance_det_en;
 44     mbhc->hphl_swh = hph_swh;
 45     mbhc->gnd_swh = gnd_swh;
 46     mbhc->micbias_enable = false;
 47     mbhc->mbhc_cb = mbhc_cb;
 48     mbhc->btn_press_intr = false;
 49 
 50     if (mbhc->intr_ids == NULL) {
 51         pr_err("%s: Interrupt mapping not provided\n", __func__);
 52         return -EINVAL;
 53     }
 54 
 55     if (mbhc->headset_jack.jack == NULL) {
 56         ret = snd_soc_jack_new(codec, "Headset Jack",
 57                 WCD_MBHC_JACK_MASK, &mbhc->headset_jack);
 58         if (ret) {
 59             pr_err("%s: Failed to create new jack\n", __func__);
 60             return ret;
 61         }
 62 
 63         ret = snd_soc_jack_new(codec, "Button Jack",
 64                        WCD_MBHC_JACK_BUTTON_MASK,
 65                        &mbhc->button_jack);
 66         if (ret) {
 67             pr_err("Failed to create new jack\n");
 68             return ret;
 69         }
 70 
 71         ret = snd_jack_set_key(mbhc->button_jack.jack,
 72                        SND_JACK_BTN_0,
 73                        KEY_MEDIA);
 74         if (ret) {
 75             pr_err("%s: Failed to set code for btn-0\n",
 76                 __func__);
 77             return ret;
 78         }
 79 
 80         INIT_DELAYED_WORK(&mbhc->mbhc_btn_dwork, wcd_btn_lpress_fn);
 81     }
 82 
 83     /* Register event notifier */
 84     mbhc->nblock.notifier_call = wcd_event_notify;
 85     ret = msm8x16_register_notifier(codec, &mbhc->nblock);
 86     if (ret) {
 87         pr_err("%s: Failed to register notifier %d\n", __func__, ret);
 88         return ret;
 89     }
 90 
 91     init_waitqueue_head(&mbhc->wait_btn_press);
 92     mutex_init(&mbhc->codec_resource_lock);
 93 
 94     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->mbhc_sw_intr,
 95                   wcd_mbhc_mech_plug_detect_irq,
 96                   "mbhc sw intr", mbhc);
 97     if (ret) {
 98         pr_err("%s: Failed to request irq %d, ret = %d\n", __func__,
 99                mbhc->intr_ids->mbhc_sw_intr, ret);
100         goto err_mbhc_sw_irq;
101     }
102 
103     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->mbhc_btn_press_intr,
104                   wcd_mbhc_btn_press_handler,
105                   "Button Press detect",
106                   mbhc);
107     if (ret) {
108         pr_err("%s: Failed to request irq %d\n", __func__,
109                mbhc->intr_ids->mbhc_btn_press_intr);
110         goto err_btn_press_irq;
111     }
112 
113     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->mbhc_btn_release_intr,
114                   wcd_mbhc_release_handler,
115                   "Button Release detect", mbhc);
116     if (ret) {
117         pr_err("%s: Failed to request irq %d\n", __func__,
118             mbhc->intr_ids->mbhc_btn_release_intr);
119         goto err_btn_release_irq;
120     }
121 
122     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->mbhc_hs_ins_intr,
123                   wcd_mbhc_hs_ins_irq,
124                   "Elect Insert", mbhc);
125     if (ret) {
126         pr_err("%s: Failed to request irq %d\n", __func__,
127                mbhc->intr_ids->mbhc_hs_ins_intr);
128         goto err_mbhc_hs_ins_irq;
129     }
130     wcd9xxx_spmi_disable_irq(mbhc->intr_ids->mbhc_hs_ins_intr);
131 
132     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->mbhc_hs_rem_intr,
133                   wcd_mbhc_hs_rem_irq,
134                   "Elect Remove", mbhc);
135     if (ret) {
136         pr_err("%s: Failed to request irq %d\n", __func__,
137                mbhc->intr_ids->mbhc_hs_rem_intr);
138         goto err_mbhc_hs_rem_irq;
139     }
140     wcd9xxx_spmi_disable_irq(mbhc->intr_ids->mbhc_hs_rem_intr);
141 
142     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->hph_left_ocp,
143                   wcd_mbhc_hphl_ocp_irq, "HPH_L OCP detect",
144                   mbhc);                          //在这里申请对detect管脚的判断中断
145     if (ret) {
146         pr_err("%s: Failed to request irq %d\n", __func__,
147                mbhc->intr_ids->hph_left_ocp);
148         goto err_hphl_ocp_irq;
149     }
150 
151     ret = wcd9xxx_spmi_request_irq(mbhc->intr_ids->hph_right_ocp,
152                   wcd_mbhc_hphr_ocp_irq, "HPH_R OCP detect",
153                   mbhc);
154     if (ret) {
155         pr_err("%s: Failed to request irq %d\n", __func__,
156                mbhc->intr_ids->hph_right_ocp);
157         goto err_hphr_ocp_irq;
158     }
159 
160     pr_debug("%s: leave ret %d\n", __func__, ret);
161     return ret;
162 
163 err_hphr_ocp_irq:
164     wcd9xxx_spmi_free_irq(mbhc->intr_ids->hph_left_ocp, mbhc);
165 err_hphl_ocp_irq:
166     wcd9xxx_spmi_free_irq(mbhc->intr_ids->mbhc_hs_rem_intr, mbhc);
167 err_mbhc_hs_rem_irq:
168     wcd9xxx_spmi_free_irq(mbhc->intr_ids->mbhc_hs_ins_intr, mbhc);
169 err_mbhc_hs_ins_irq:
170     wcd9xxx_spmi_free_irq(mbhc->intr_ids->mbhc_btn_release_intr, mbhc);
171 err_btn_release_irq:
172     wcd9xxx_spmi_free_irq(mbhc->intr_ids->mbhc_btn_press_intr, mbhc);
173 err_btn_press_irq:
174     wcd9xxx_spmi_free_irq(mbhc->intr_ids->mbhc_sw_intr, mbhc);
175 err_mbhc_sw_irq:
176     msm8x16_unregister_notifier(codec, &mbhc->nblock);
177     mutex_destroy(&mbhc->codec_resource_lock);
178 err:
179     pr_debug("%s: leave ret %d\n", __func__, ret);
180     return ret;
181 }
 1 static irqreturn_t wcd_mbhc_mech_plug_detect_irq(int irq, void *data)
 2 {
 3     int r = IRQ_HANDLED;
 4     struct wcd_mbhc *mbhc = data;
 5 
 6     pr_debug("%s: enter\n", __func__);
 7     if (unlikely(wcd9xxx_spmi_lock_sleep() == false)) {
 8         pr_warn("%s: failed to hold suspend\n", __func__);
 9         r = IRQ_NONE;
10     } else {
11         /* Call handler */
12         wcd_mbhc_swch_irq_handler(mbhc);        //中断函数中的接口,负责处理相应的
13         wcd9xxx_spmi_unlock_sleep();
14     }
15     pr_debug("%s: leave %d\n", __func__, r);
16     return r;
17 }
  1 static void wcd_mbhc_swch_irq_handler(struct wcd_mbhc *mbhc)
  2 {
  3     bool detection_type;
  4     bool micbias1;
  5     struct snd_soc_codec *codec = mbhc->codec;
  6     pr_debug("%s: enter\n", __func__);
  7 
  8     WCD_MBHC_RSC_LOCK(mbhc);
  9 
 10     mbhc->in_swch_irq_handler = true;
 11 
 12     /* cancel pending button press */
 13     if (wcd_cancel_btn_work(mbhc))
 14         pr_debug("%s: button press is canceled\n", __func__);
 15 
 16     detection_type = (snd_soc_read(codec,
 17                 MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_1)) & 0x20;
 18 
 19     /* Set the detection type appropriately */
 20     snd_soc_update_bits(codec, MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_1,
 21             0x20, (!detection_type << 5));
 22 
 23     pr_debug("%s: mbhc->current_plug: %d detection_type: %d\n", __func__,
 24             mbhc->current_plug, detection_type);
 25     wcd_cancel_hs_detect_plug(mbhc, &mbhc->correct_plug_swch);
 26 
 27     micbias1 = (snd_soc_read(codec, MSM8X16_WCD_A_ANALOG_MICB_1_EN) & 0x80);
 28     if ((mbhc->current_plug == MBHC_PLUG_TYPE_NONE) &&
 29         detection_type) {
 30         /* Make sure MASTER_BIAS_CTL is enabled */
 31         snd_soc_update_bits(codec,
 32                     MSM8X16_WCD_A_ANALOG_MASTER_BIAS_CTL,
 33                     0x30, 0x30);
 34         snd_soc_update_bits(codec,
 35                 MSM8X16_WCD_A_ANALOG_MICB_1_EN,
 36                 0x04, 0x04);
 37         if (!mbhc->mbhc_cfg->hs_ext_micbias)
 38             /* Enable Tx2 RBias if the headset
 39              * is using internal micbias*/
 40             snd_soc_update_bits(codec,
 41                     MSM8X16_WCD_A_ANALOG_MICB_1_INT_RBIAS,
 42                     0x10, 0x10);
 43         /* Remove pull down on MIC BIAS2 */
 44         snd_soc_update_bits(codec,
 45                  MSM8X16_WCD_A_ANALOG_MICB_2_EN,
 46                 0x20, 0x00);
 47         /* Enable HW FSM */
 48         snd_soc_update_bits(codec,
 49                 MSM8X16_WCD_A_ANALOG_MBHC_FSM_CTL,
 50                 0x80, 0x80);
 51         /* Apply trim if needed on the device */
 52         if (mbhc->mbhc_cb && mbhc->mbhc_cb->trim_btn_reg)
 53             mbhc->mbhc_cb->trim_btn_reg(codec);
 54         /* Enable external voltage source to micbias if present */
 55         if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source)
 56             mbhc->mbhc_cb->enable_mb_source(codec, true);
 57         mbhc->btn_press_intr = false;
 58         wcd_mbhc_detect_plug_type(mbhc);
 59     } else if ((mbhc->current_plug != MBHC_PLUG_TYPE_NONE)
 60             && !detection_type) {
 61         /* Disable external voltage source to micbias if present */
 62         if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source)
 63             mbhc->mbhc_cb->enable_mb_source(codec, false);
 64         /* Disable HW FSM */
 65         snd_soc_update_bits(codec,
 66                 MSM8X16_WCD_A_ANALOG_MBHC_FSM_CTL,
 67                 0xB0, 0x00);
 68         snd_soc_update_bits(codec,
 69                 MSM8X16_WCD_A_ANALOG_MICB_1_EN,
 70                 0x04, 0x00);
 71         if (mbhc->mbhc_cb && mbhc->mbhc_cb->set_cap_mode)
 72             mbhc->mbhc_cb->set_cap_mode(codec, micbias1, false);
 73         mbhc->btn_press_intr = false;
 74         if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) {        //如果判断是headphone,上报数据;
 75             wcd_mbhc_report_plug(mbhc, 0, SND_JACK_HEADPHONE);
 76         } else if (mbhc->current_plug == MBHC_PLUG_TYPE_GND_MIC_SWAP) {
 77             wcd_mbhc_report_plug(mbhc, 0, SND_JACK_UNSUPPORTED);
 78         } else if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET) {
 79             /* make sure to turn off Rbias */
 80             snd_soc_update_bits(codec,
 81                     MSM8X16_WCD_A_ANALOG_MICB_1_INT_RBIAS,
 82                     0x18, 0x08);
 83             snd_soc_update_bits(codec,
 84                     MSM8X16_WCD_A_ANALOG_MICB_2_EN,
 85                     0x20, 0x20);
 86             wcd9xxx_spmi_disable_irq(
 87                     mbhc->intr_ids->mbhc_hs_rem_intr);
 88             wcd9xxx_spmi_disable_irq(
 89                     mbhc->intr_ids->mbhc_hs_ins_intr);
 90             snd_soc_update_bits(codec,
 91                     MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_1,
 92                     0x01, 0x01);
 93             snd_soc_update_bits(codec,
 94                     MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_2,
 95                     0x06, 0x00);
 96             wcd_mbhc_report_plug(mbhc, 0, SND_JACK_HEADSET);
 97         } else if (mbhc->current_plug == MBHC_PLUG_TYPE_HIGH_HPH) {
 98             mbhc->is_extn_cable = false;
 99             wcd9xxx_spmi_disable_irq(
100                     mbhc->intr_ids->mbhc_hs_rem_intr);
101             wcd9xxx_spmi_disable_irq(
102                     mbhc->intr_ids->mbhc_hs_ins_intr);
103             snd_soc_update_bits(codec,
104                     MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_1,
105                     0x01, 0x01);
106             snd_soc_update_bits(codec,
107                     MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_2,
108                     0x06, 0x00);
109             wcd_mbhc_report_plug(mbhc, 0, SND_JACK_LINEOUT);
110         }
111     } else if (!detection_type) {
112         /* Disable external voltage source to micbias if present */
113         if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source)
114             mbhc->mbhc_cb->enable_mb_source(codec, false);
115         /* Disable HW FSM */
116         snd_soc_update_bits(codec,
117                 MSM8X16_WCD_A_ANALOG_MBHC_FSM_CTL,
118                 0xB0, 0x00);
119     }
120 
121     mbhc->in_swch_irq_handler = false;
122     WCD_MBHC_RSC_UNLOCK(mbhc);
123     pr_debug("%s: leave\n", __func__);
124 }

经过一系列的检测,判断是headset,headphones等,如果是headphones,最终通过wcd_mbhc_jack_report将数据汇报上去。

  1 static void wcd_mbhc_report_plug(struct wcd_mbhc *mbhc, int insertion,
  2                 enum snd_jack_types jack_type)
  3 {
  4     struct snd_soc_codec *codec = mbhc->codec;
  5     WCD_MBHC_RSC_ASSERT_LOCKED(mbhc);
  6 
  7     pr_debug("%s: enter insertion %d hph_status %x\n",
  8          __func__, insertion, mbhc->hph_status);
  9     if (!insertion) {
 10         /* Report removal */
 11         mbhc->hph_status &= ~jack_type;
 12         /*
 13          * cancel possibly scheduled btn work and
 14          * report release if we reported button press
 15          */
 16         if (wcd_cancel_btn_work(mbhc)) {
 17             pr_debug("%s: button press is canceled\n", __func__);
 18         } else if (mbhc->buttons_pressed) {
 19             pr_debug("%s: release of button press%d\n",
 20                  __func__, jack_type);
 21             wcd_mbhc_jack_report(mbhc, &mbhc->button_jack, 0,
 22                         mbhc->buttons_pressed);
 23             mbhc->buttons_pressed &=
 24                 ~WCD_MBHC_JACK_BUTTON_MASK;
 25         }
 26 
 27         if (mbhc->micbias_enable)
 28             mbhc->micbias_enable = false;
 29 
 30         mbhc->zl = mbhc->zr = 0;
 31         mbhc->is_hs_inserted = false;
 32         pr_debug("%s: Reporting removal %d(%x)\n", __func__,
 33              jack_type, mbhc->hph_status);
 34         wcd_mbhc_jack_report(mbhc, &mbhc->headset_jack,
 35                 mbhc->hph_status, WCD_MBHC_JACK_MASK);
 36         wcd_mbhc_set_and_turnoff_hph_padac(mbhc);
 37         hphrocp_off_report(mbhc, SND_JACK_OC_HPHR);
 38         hphlocp_off_report(mbhc, SND_JACK_OC_HPHL);
 39         mbhc->current_plug = MBHC_PLUG_TYPE_NONE;
 40     } else {
 41         /*
 42          * Report removal of current jack type.
 43          * Headphone to headset shouldn't report headphone
 44          * removal.
 45          */
 46         if (mbhc->mbhc_cfg->detect_extn_cable &&
 47             (mbhc->current_plug == MBHC_PLUG_TYPE_HIGH_HPH ||
 48             jack_type == SND_JACK_LINEOUT) &&
 49             (mbhc->hph_status && mbhc->hph_status != jack_type)) {
 50 
 51         if (mbhc->micbias_enable)
 52             mbhc->micbias_enable = false;
 53 
 54             mbhc->zl = mbhc->zr = 0;
 55             mbhc->is_hs_inserted = false;
 56             pr_debug("%s: Reporting removal (%x)\n",
 57                  __func__, mbhc->hph_status);
 58             wcd_mbhc_jack_report(mbhc, &mbhc->headset_jack,
 59                         0, WCD_MBHC_JACK_MASK);
 60 
 61             if (mbhc->hph_status == SND_JACK_LINEOUT) {
 62 
 63                 pr_debug("%s: Enable micbias\n", __func__);
 64                 /* Disable current source and enable micbias */
 65                 snd_soc_update_bits(codec,
 66                     MSM8X16_WCD_A_ANALOG_MBHC_FSM_CTL,
 67                     0xB0, 0x80);
 68                 snd_soc_update_bits(codec,
 69                     MSM8X16_WCD_A_ANALOG_MICB_2_EN,
 70                     0x80, 0x80);
 71 
 72                 pr_debug("%s: set up elec removal detection\n",
 73                       __func__);
 74                 snd_soc_update_bits(codec,
 75                     MSM8X16_WCD_A_ANALOG_MBHC_DET_CTL_1,
 76                     0x01, 0x00);
 77                 usleep_range(200, 210);
 78                 wcd9xxx_spmi_enable_irq(
 79                     mbhc->intr_ids->mbhc_hs_rem_intr);
 80             }
 81             mbhc->hph_status &= ~(SND_JACK_HEADSET |
 82                         SND_JACK_LINEOUT |
 83                         SND_JACK_UNSUPPORTED);
 84         }
 85 
 86         if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET &&
 87             jack_type == SND_JACK_HEADPHONE)
 88             mbhc->hph_status &= ~SND_JACK_HEADSET;
 89 
 90         /* Report insertion */
 91         mbhc->hph_status |= jack_type;
 92 
 93         if (jack_type == SND_JACK_HEADPHONE)
 94             mbhc->current_plug = MBHC_PLUG_TYPE_HEADPHONE;
 95         else if (jack_type == SND_JACK_UNSUPPORTED)
 96             mbhc->current_plug = MBHC_PLUG_TYPE_GND_MIC_SWAP;
 97         else if (jack_type == SND_JACK_HEADSET) {
 98             mbhc->current_plug = MBHC_PLUG_TYPE_HEADSET;
 99             mbhc->jiffies_atreport = jiffies;
100         }
101         else if (jack_type == SND_JACK_LINEOUT)
102             mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH;
103 
104         if (mbhc->impedance_detect)
105             wcd_mbhc_calc_impedance(mbhc,
106                     &mbhc->zl, &mbhc->zr);
107         mbhc->is_hs_inserted = true;
108         pr_debug("%s: Reporting insertion %d(%x)\n", __func__,
109              jack_type, mbhc->hph_status);
110         wcd_mbhc_jack_report(mbhc, &mbhc->headset_jack,
111                     mbhc->hph_status, WCD_MBHC_JACK_MASK);
112         wcd_mbhc_clr_and_turnon_hph_padac(mbhc);
113     }
114     pr_debug("%s: leave hph_status %x\n", __func__, mbhc->hph_status);
115 }
1 static void wcd_mbhc_jack_report(struct wcd_mbhc *mbhc,
2                 struct snd_soc_jack *jack, int status, int mask)
3 {
4     snd_soc_jack_report_no_dapm(jack, status, mask);
5 }
1 void snd_soc_jack_report_no_dapm(struct snd_soc_jack *jack, int status,
2                  int mask)
3 {
4     jack->status &= ~mask;
5     jack->status |= status & mask;
6 
7     snd_jack_report(jack->jack, jack->status);
8 }
9 EXPORT_SYMBOL_GPL(snd_soc_jack_report_no_dapm);
 1 void snd_jack_report(struct snd_jack *jack, int status)
 2 {
 3     int i;
 4 
 5     if (!jack)
 6         return;
 7 
 8     for (i = 0; i < ARRAY_SIZE(jack->key); i++) {
 9         int testbit = SND_JACK_BTN_0 >> i;
10 
11         if (jack->type & testbit)
12             input_report_key(jack->input_dev, jack->key[i],
13                      status & testbit);
14     }
15 
16     for (i = 0; i < ARRAY_SIZE(jack_switch_types); i++) {
17         int testbit = 1 << i;
18         if (jack->type & testbit)
19             input_report_switch(jack->input_dev,
20                         jack_switch_types[i],
21                         status & testbit);
22     }
23 
24     input_sync(jack->input_dev);      //上报键值
25 }
26 EXPORT_SYMBOL(snd_jack_report);

最终汇报上去的有效数据是5   6   1 (插头类型 耳机信号 值插入)

            0   0   0(同步)

插入的时候:

拔出的时候:

然后也可以根据高通文档判断是否是handset还是handphone:

高通是通过申请为/dev/input/event事件来确定的;

handset插入事件:

handset拔出事件:

本文参与腾讯云自媒体分享计划,欢迎正在阅读的你也加入,一起分享。

发表于

我来说两句

0 条评论
登录 后参与评论

相关文章

来自专栏草根专栏

Typescript 查缺补漏

Types Casting: let input = xxx as HTMLInputElement; let input = <HTMLElement>xxx...

2033
来自专栏杨建荣的学习笔记

一个MySQL死锁问题的复现

很久之前有一个同事问我一个关于死锁的问题,一直在拖这个事情,总算找了空来看看。 这个环境的事务隔离级别是RR,仔细看了下问题描述和背景,发现还真不是一...

3399
来自专栏张善友的专栏

通过SmtpClient发送Exchange会议邮件

看到C#中调用Outlook API 发起会议 ,这个完全可以用SMTP方式实现的,下面我的项目中使用的代码: 对于.NET而言,从2.0开始,发邮件已经是一件...

1779
来自专栏函数式编程语言及工具

PICE(4):MongoDBStreaming - gRPC Protobuf conversion

   前两篇我们介绍了JDBC和Cassandra的gRPC streaming实现。相对MongoDB来说,JDBC和Cassandra支持字符类型的quer...

740
来自专栏乐沙弥的世界

ORA-02409:超时:分布式事务处理等待锁定ORA-02063

ORA-02409:超时:分布式事务处理等待锁定ORA-02063 一、错误现象与环境     前端应用程序运行时出现下面的错误提示: 事件添加失败:O...

732
来自专栏码匠的流水账

列出spring security的所有SecurityFilterChain

spring-security-config-4.1.4.RELEASE-sources.jar!/org/springframework/security/c...

542
来自专栏王磊的博客

C# 控制台应用程序输出颜色字体[更正版]

首先感谢院子里的“yanxinchen”,之前的方法是通过c#调用系统api实现的,相比之下我的有点画蛇添足了,哈哈。 最佳解决方案的代码: static vo...

3518
来自专栏JadePeng的技术博客

HtmlAgilityPack 库 StackOverflowException 解决方案

     最近试用HtmlAgilityPack 来解析html,试用过程中程序会抛出StackOverflowException异常,从MSDN上可以看到,从...

2645
来自专栏增长技术

Android 图片功能模块相关库

If you want to let your users choose crop ratio dynamically, just do not call wi...

542
来自专栏一个会写诗的程序员的博客

java.base.jmod

/Library/Java/JavaVirtualMachines/jdk-9.jdk/Contents/Home/jmods$ jmod list java....

742

扫描关注云+社区