wireguard安装与配置

sudo apt-get install wireguard

# 开启ipv4流量转发
echo "net.ipv4.ip_forward = 1" >> /etc/sysctl.conf
sysctl -p

# 创建并进入WireGuard文件夹
mkdir -p /etc/wireguard && chmod 0777 /etc/wireguard
cd /etc/wireguard
umask 077

# 生成服务器和客户端密钥对
wg genkey | tee server_privatekey | wg pubkey > server_publickey
wg genkey | tee client_privatekey | wg pubkey > client_publickey

##########################生成服务端的配置文件 /etc/wireguard/wg0.conf##########################
echo "
[Interface]
PrivateKey = $(cat server_privatekey) # 填写本机的privatekey 内容
Address = 10.0.8.1/24
PostUp   = iptables -A FORWARD -i wg0 -j ACCEPT; iptables -A FORWARD -o wg0 -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
PostDown = iptables -D FORWARD -i wg0 -j ACCEPT; iptables -D FORWARD -o wg0 -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE
ListenPort = 50814 # 注意该端口是UDP端口
DNS = 8.8.8.8
MTU = 1420
[Peer]
PublicKey =  $(cat client_publickey)  # 填写对端的publickey 内容
AllowedIPs = 10.0.8.10/24 " > wg0.conf
# 设置开机自启
systemctl enable wg-quick@wg0
# 重要！如果名字不是eth0, 以下PostUp和PostDown处里面的eth0替换成自己服务器显示的名字
# ListenPort为端口号，可以自己设置想使用的数字
# 以下内容一次性粘贴执行，不要分行执行



##########################生成客户端的配置文件 /etc/wireguard/client.conf##########################
echo "
[Interface]
  PrivateKey = $(cat client_privatekey)  # 填写本机的privatekey 内容
  Address = 10.0.8.10/24
  DNS = 8.8.8.8
  MTU = 1420

[Peer]
  PublicKey = $(cat server_publickey)  # 填写对端的publickey 内容
  Endpoint = server公网的IP:50814
  AllowedIPs = 0.0.0.0/0, ::0/0
  PersistentKeepalive = 25 " > client.conf
 # 注：文件在服务端配好了可以下载下来传到客户端

########################服务端###################
# 启动WireGuard
wg-quick up wg0
# 停止WireGuard
wg-quick down wg0
# 查看WireGuard运行状态
[root@localhost~]# wg
interface: wg0
  public key: b8fztAWxqS/SKQ619YTM09siKESbzoUiBeautnFsaGU=
  private key: (hidden)
  listening port: 50814

peer: HF7vS/rpk2tEQ1WxWnh78Rp8lSuwEMLISqQsX6MFlwk=
  endpoint: 221.225.202.158:11562
  allowed ips: 10.0.8.0/24
  latest handshake: 34 seconds ago
  transfer: 16.26 KiB received, 12.87 KiB sent


########################客户端###################
# 启动WireGuard
wg-quick up client
# 停止WireGuard
wg-quick down client
# 查看WireGuard运行状态
[root@localhost~]# wg
[root@v2 ~]# wg
interface: client
  public key: HF7vS/rpk2tEQ1WxWnh78Rp8lSuwEMLISqQsX6MFlwk=
  private key: (hidden)
  listening port: 59633
  fwmark: 0xca6c

peer: b8fztAWxqS/SKQ619YTM09siKESbzoUiBeautnFsaGU=
  endpoint: server公网的IP:50814
  allowed ips: 0.0.0.0/0, ::/0
  latest handshake: 17 seconds ago
  transfer: 9.96 KiB received, 19.09 KiB sent
  persistent keepalive: every 25 seconds

ping 10.0.8.1

[root@v2 ~]# ip route add 103.52.188.136 via 192.168.1.2 
[root@v2 ~]# ip route add 0.0.0.0/0 via 10.0.8.1   # 所有的流量都走这个ip

apt -y install tcpdump
# 监视指定网络接口的数据包 
tcpdump -i wg0 # 我们的转发都是经过这个私网来进行的可以客户ping的同时，服务端进行抓包查看

apt-get install qrencode

qrencode -t ansiutf8 < client.conf

# ip link add dev wg0 type wireguard

# ip address add dev wg0 192.168.2.1/24

# ip address add dev wg0 192.168.2.1 peer 192.168.2.2

# wg setconf wg0 myconfig.conf

# wg set wg0 listen-port 51820 private-key /path/to/private-key peer ABCDEF... allowed-ips 192.168.88.0/24 endpoint 209.202.254.14:8172

# ip link set up dev wg0

$ umask 077
$ wg genkey > privatekey

$ wg pubkey < privatekey > publickey

$ wg genkey | tee privatekey | wg pubkey > publickey