18-GPRS(Air202)拨打电话

例如存入的号码
姓名 号码 
1 10086
2 10010
... ....

 

例如存入的号码
01 0501 05代表所有的号码循环拨打5次 01代表延时1小时后重复


GPIO4控制打电话(低电平有效)

开机以后先读取手机卡里面的信息,筛选出来姓名1-99 和对应的号码

取出01对应的次数 5 时间间隔 1小时

读取完成以后如果GPIO4为低电平,先拨打姓名1对应的号码,如果后面还有2 间隔50S就会再拨打2对应的号码,如果还有3,4,5....依次排着拨打
顺序拨打完一遍 次数加1 顺序拨打5次 延时1小时 然后 循环

module(...,package.seeall)
require"cc"
require"pb"
require"sys"
require"net"
require"pins"
require"common"

--[[
GPIO4低电平拨打电话
GPIO5,GPIO6,GPIO7信号强度指示
]]

local function print(...)
    _G.print("testCall",...)
end

local ReadTelephoneTable={};
local ReadTelephoneTableCopy={};
local ReadTelephoneCnt=1;
local ReadErr=0;
local LoopCnt=0;
local DelayHour=0;
local CallReadyFlage=0;
local j=1;
local CallMax = 0;
local CallCnt = 0;
local DelayCallValue = 50000;
local InputState = 0;
local ReadTelephoneSuccess = 0;--是否读取号码完成

InputKey = pio.P0_4;--输入按钮
Led1 = pio.P0_5;--Led1
Led2 = pio.P0_6;--Led2
Led3 = pio.P0_7;--Led3
pio.pin.setdir(pio.OUTPUT,InputKey)
pio.pin.setval(1,InputKey)

pio.pin.setdir(pio.OUTPUT,Led1)
pio.pin.setval(1,Led1)

pio.pin.setdir(pio.OUTPUT,Led2)
pio.pin.setval(1,Led2)

pio.pin.setdir(pio.OUTPUT,Led3)
pio.pin.setval(1,Led3)


function ReadTelephone()
    pb.read(ReadTelephoneCnt, readcb)
end

--[[小于70小时,大于35小时使用]]
function Delay35Hour() 
    sys.timerStart(CallTelephoneLoop,(DelayHour-35) * 60 * 60 * 1000) 
end
--[[小于100小时,大于70小时使用]]
function Delay35HourA()
    sys.timerStart(CallTelephoneLoop,(DelayHour-70) * 60 * 60 * 1000)
end
--[[小于100小时,大于70小时使用]]
function Delay35HourB()
    sys.timerStart(Delay35HourA,35 * 60 * 60 * 1000)
end

--[[拨打电话]]
function CallTelephoneLoop()
    if  j<= CallMax and CallMax>=1 and DelayHour >= 1 and LoopCnt>=1 then
        cc.dial(ReadTelephoneTableCopy[j]);
        sys.timerStart(cc.hangUp,30000,ReadTelephoneTableCopy[j])
        print("拨打::"..ReadTelephoneTableCopy[j]);
        j=j+1;
        if  j > CallMax  then--循环了一遍
            j = 1;
            CallCnt = CallCnt + 1;
            print("循环次数:"..CallCnt);
        end
        if  CallCnt >= LoopCnt  then--循环了设置的次数
            CallCnt = 0;
            print("开始延时:"..DelayHour.."小时");
            if  DelayHour <=35  then
                sys.timerStart(CallTelephoneLoop,DelayHour * 60 * 60 * 1000)
            elseif  DelayHour <=70  then
                sys.timerStart(Delay35Hour,35 * 60 * 60 * 1000)
            elseif  DelayHour <=100  then
                sys.timerStart(Delay35HourB,35 * 60 * 60 * 1000)
            end
        else
            print("循环");
            sys.timerStart(CallTelephoneLoop,DelayCallValue)
        end
    end
end


--[[读取号码]]
function readcb(result,name,number)
    if  result == true  then
        ReadTelephoneCnt = ReadTelephoneCnt +1;
        print(result,name,number);
        print("ReadTelephoneCnt"..ReadTelephoneCnt);
        if  string.len(name)>0  then
            ReadErr = 0;
            if  string.len(number)>0  then
                ReadErr = 0;
                ReadTelephoneTable[name] = number;
            end
        else
            if  string.len(number)==0 and string.len(name)==0 then
                print("ReadErr = ReadErr +1");
                ReadErr = ReadErr +1;
                if  ReadErr>5  then
                    ReadErr = 0;
                    sys.timerStop(ReadTelephone,1);
                    print("timerStop");
                    local i=1;
                    for key,value in pairs(ReadTelephoneTable) do
                        print(key,value)
                        if  key == "01" then
                            LoopCnt = tonumber(string.sub(value,1,2))
                            if  LoopCnt>99 or LoopCnt<1 then
                                LoopCnt = 0;
                            end
                            DelayHour = tonumber(string.sub(value,3,4))
                            if  DelayHour>99 or DelayHour<1 then
                                DelayHour = 0;
                            end
                            print("DelayHour"..DelayHour)  
                        else
                            print("key"..key)  
                            if  tonumber(key)~=nil and tonumber(key) <99 and tonumber(key)>0  then
                                ReadTelephoneTableCopy[i] = value;
                                i = i + 1;
                            end
                        end
                    end
                    CallMax = i - 1;
                    ReadTelephoneSuccess  = 1;
                end
            end
        end
        if  string.len(number)>0 then
            ReadErr = 0;    
            print("string.len(number)>0 ReadErr = 0");
        end
    else
        print(result,name,number);
    end
end

local InputCnt = 0;
local cnt = 0;
function  InputShowLed()
    if  pio.pin.getval(InputKey) == 0 then
        InputCnt = InputCnt +1;
        if  InputCnt>6 and InputState==0 then
            InputCnt = 0;
            if  ReadTelephoneSuccess == 1  then
                InputState = 1;
                j=1;
                CallCnt = 0;
                sys.timerStopAll(CallTelephoneLoop)
                sys.timerStart(CallTelephoneLoop,1)
            end
        end
    else
        InputCnt = 0;
        InputState = 0;
        sys.timerStopAll(CallTelephoneLoop)
    end
    cnt = cnt +1;
    if  cnt>100  then
        cnt = 0;
        print("信号强度:"..net.getRssi())
        if  net.getRssi() == 0  then
            pio.pin.setval(0,Led1);--用三个指示灯指示信号的强度
            pio.pin.setval(0,Led2);
            pio.pin.setval(0,Led3); 
        elseif  net.getRssi()<10 then
            pio.pin.setval(0,Led1);
            pio.pin.setval(0,Led2);
            pio.pin.setval(1,Led3); 
        elseif  net.getRssi()<20 then
            pio.pin.setval(0,Led1);
            pio.pin.setval(1,Led2);
            pio.pin.setval(1,Led3); 
        elseif  net.getRssi()>20 then
            pio.pin.setval(1,Led1);
            pio.pin.setval(1,Led2);
            pio.pin.setval(1,Led3); 
        end
    end
end

--[[可以打电话]]
local function CallReadyMethod()
    CallReadyFlage = 1;
    print("*****************************CALL_READY*****************************");
end
---对方接听
-- string num，建立通话的对方号码
local function connected(num)
    print("主动结束通话")
    cc.hangUp(num)
end

--结束通话
local function disconnected(para)
    print("disconnected:"..(para or "nil"))
end

sys.timerLoopStart(ReadTelephone,1000,1)
sys.subscribe("CALL_CONNECTED",connected)
sys.subscribe("CALL_READY",CallReadyMethod)
sys.subscribe("CALL_DISCONNECTED",disconnected)
sys.timerLoopStart(InputShowLed,10)
cc.dtmfDetect(true)