前往小程序,Get更优阅读体验!
立即前往
首页
学习
活动
专区
工具
TVP
发布
社区首页 >专栏 >CISCO交换机命令全集(3)

CISCO交换机命令全集(3)

作者头像
py3study
发布2020-01-08 15:08:18
7340
发布2020-01-08 15:08:18
举报
文章被收录于专栏:python3

60.配置HSRP跟踪:

router(config-if)# standy group-number track type-number interface-priority

61.要显示HSRP路由器的状态:

router# show standby type-number group brief

62.用命令show ip igmp确定当选的查询器。

63.启动IP组播路由选择:

router(config)# ip muticast-routing

64.启动接口上的PIM:

dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}

65.启动稀疏-稠密模式下的PIM:

router# ip multicast-routing

router# interface type number

router# ip pim sparse-dense-mode

66.核实PIM的配置:

dallasr1># show ip pim interface[type number] [count]

67.显示PIM邻居:

dallasr1># show ip neighbor type number

68.为了配置RP的地址,命令如下:

dallasr1># ip pim rp-address ip-address [group-access-list-number][override]

69.选择一个默认的RP:

dallasr1># ip pim rp-address

通告RP和它所服务的组范围:

dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number

为管理范围组通告RP的地址:

dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1

dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255

设定一个RP映像代理:

dallasr1># ip pim send-rp-discovery scope ttl

核实组到RP的映像:

dallasr1># show ip pim rp mapping

dallasr1># show ip pim rp [group-name|group-address] [mapping]

70.在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL阀值:

dallasr1>(config-if)# ip multicast ttl-threshold ttl-value

71.用show ip pim neighbor显示PIM邻居表。

72.显示组播通信路由表中的各条记录:

dallasr1>show ip mroute [group-name|group-address][scoure][summary][count][active kbps]

73.要记录一个路由器接受和发送的全部IP组播包:

dallasr1> #debug ip mpacket [detail] [access-list][group]

74.要在CISCO路由器上配置CGMP:

dallasr1>(config-if)# ip cgmp

75.配置一个组播路由器,使之加入某一个特定的组播组:

dallasr1>(config-if)# ip igmp join-group group-address

76.关闭 CGMP:

dallasr1>(config-if)# no ip cgmp

77.启动交换机上的CGMP:

dallasr1>(enable) set cgmp enable

78.核实Catalyst交换机上CGMP的配置情况:

catalystla1>(enable) show config

set prompt catalystla1>

set interface sc0 192.168.1.1 255.255.255.0

set cgmp enable

79.CGMP离开的设置:

Dallas_SW(enable) set cgmp leave

80.在Cisco设备上修改控制端口密码:

R1(config)# line console 0

R1(config-line)# login

R1(config-line)# password Lisbon

R1(config)# enable password Lilbao

R1(config)# login local

R1(config)# username student password cisco

81.在Cisco设备上设置控制台及vty端口的会话超时:

R1(config)# line console 0

R1(config-line)# exec-timeout 5 10

R1(config)# line vty 0 4

R1(config-line)# exec-timeout 5 2

82.在Cisco设备上设定特权级:

R1(config)# privilege configure level 3 username

R1(config)# privilege configure level 3 copy run start

R1(config)# privilege configure level 3 ping

R1(config)# privilege configure level 3 show run

R1(config)# enable secret level 3 cisco

83.使用命令privilege 可定义在该特权级下使用的命令:

router(config)# privilege mode level level command

84.设定用户特权级:

router(config)# enable secret level 3 dallas

router(config)# enable secret san-fran

router(config)# username student password cisco

85.标志设置与显示:

R1(config)# banner motd ‘unauthorized access will be prosecuted!’

86.设置vty访问:

R1(config)# access-list 1 permit 192.168.2.5

R1(config)# line vty 0 4

R1(config)# access-class 1 in

87.配置HTTP访问:

Router3(config)# access-list 1 permit 192.168.10.7

Router3(config)# ip http sever

Router3(config)# ip http access-class 1

Router3(config)# ip http authentication local

Router3(config)# username student password cisco

88.要启用HTTP访问,请键入以下命令:

switch(config)# ip http sever

89.在基于set命令的交换机上用setCL1启动和核实端口安全:

switch(enable) set port security mod_num/port_num…enable mac address

switch(enable) show port mod_num/port_num

在基于CiscoIOS命令的交换机上启动和核实端口安全:

switch(config-if)# port secure [mac-mac-count maximum-MAC-count]

switch# show mac-address-table security [type module/port]

本文参与 腾讯云自媒体同步曝光计划,分享自作者个人站点/博客。
原始发表:2019/09/14 ,如有侵权请联系 cloudcommunity@tencent.com 删除

本文分享自 作者个人站点/博客 前往查看

如有侵权,请联系 cloudcommunity@tencent.com 删除。

本文参与 腾讯云自媒体同步曝光计划  ,欢迎热爱写作的你一起参与!

评论
登录后参与评论
0 条评论
热度
最新
推荐阅读
领券
问题归档专栏文章快讯文章归档关键词归档开发者手册归档开发者手册 Section 归档