我的Python和Arduino代码一起产生了最令人困惑的行为。我正在运行一个测试,看看Pyserial是否正确地写入和读取了我的Arduino,但是似乎Pyserial只在用户输入时才会写到Arduino。注意,这个用户输入甚至不需要是发送给Arduino的消息,但是只要采用这种输入,我想发送给Arduino的任何消息都会发送。如果没有用户输入,那么Pyserial没有写入Arduino,或者Arduino没有响应串行输入。
下面是我的python代码:
import serial
import time
arduino = serial.Serial(port='/dev/cu.u
我试图弄清楚如何使用可选的LED在数据显示Arduino屏蔽。我已经写了一个简单的if语句,它打开LED,但它不会关闭时,我想它。有人能帮我理解原因吗?
我使用的土壤水分传感器,我希望LED关闭时,湿度超过300。代码使用内置的LED,但我试图了解可选LED是如何工作的。
int led2 = 1;
void setup() {
Serial.begin(9600);
// open serial port, set the baud rate as 9600 bps
pinMode(led2, OUTPUT);
}
void loop() {
// Read data a
我得到一些读数从一个加速度计连接到一个Arduino,这是反过来连接到MATLAB通过串行通信。我想把读数写进文本文件。10秒的读取将写入大约1000个条目,使文本文件大小约为1k字节。
我将使用以下代码:
%%%%%// Communication %%%%%
arduino=serial('COM6','BaudRate',9600);
fopen(arduino);
fileID = fopen('Readings.txt','w');
%%%%%// Reading from Serial %%%%%
for i=1:S
我在app Inventor中制作了一个将文本发送到arduino的应用程序。文本类型:"1,1,2,2,0,0,0,2,1,0“。但是在arduino这一端,我收到了这样的东西:x€xx€xx€xx€...
为了通信,我使用HC-05蓝牙模块。而arduino是超级adk。我尝试在App Inventor中将编码设置为UTF-8和ASCII。有没有办法在不改变arduino代码的情况下做到这一点?
arduino代码:
void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
我有步进电机,我想控制他的速度。这怎么可能呢?
我使用的是Arduino UNO。
for (i = 0; i<400; i++) // Iterate for 4000 microsteps
{
digitalWrite(StepPinB, LOW); // This LOW to HIGH change is what creates the
digitalWrite(StepPinB, HIGH); // "Rising Edge" so the easydriver knows to when to step.
dela
我正在用python编写一个项目,这个项目最终应该运行在LinkIt One IoT设备上。
我编写了一些测试代码,以检查是否能够在Arduino IDE与python之间连接(我正在使用Pycharm)。
测试代码是:
import serial
import time
arduino = serial.Serial('COM1', 115200, timeout=.1)
time.sleep(1) #give the connection a second to settle
arduino.write("Hello from Python!")
w
我有一个学校项目,涉及一个基于Arduino的传感器,需要发送传感器读数到服务器通过HTTP。传感器读数不需要加密(人们知道它们是什么是正常的),但我们确实希望(1)验证Arduino和(2)确保数据在传输过程中不被更改。
毕竟,我们不希望任何人都能把传感器读数发送到服务器,我们想知道这些读数是从哪里来的。
我已经考虑过使用JSON令牌(这些令牌非常紧凑,可以硬编码到Arduino或SD卡上)来验证Arduino,但是如果我们只是使用HTTP over TCP,那么中间人攻击仍然是一个问题。推荐使用HTTPS,但我在某个地方读到Arduino不具备HTTPS所需的马力。(这是真的吗?我还没有真
我使用代码在Arduino Uno R3上的一个AC单元中读取。
有一个unsigned int rawCodes[RAWBUF]。当我将RAWBUF设置为255时,一切都很好。我把它推到256,它上传的很好,但没有反应。
这是内存限制吗?,不是。我应该能得到400个元素。
而且,因为我达到的极限是255,这让我相信还有别的事情发生。
谢谢,贾斯汀
我编写了这个示例草图来测试与Arduino Leonardo的串行通信(在Windows 7上使用Arduino IDE 1.0.5 ):
int delayTime = 10000;
long lastExec = 0;
void setup()
{
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
}
void loop()
{
long t = millis();
if (t - lastExec &g
我使用此代码将字符串从arduino发送到PC。
int i=0;
void setup(){
Serial.begin(9600); // Open serial connection at a baud rate of 9600
pinMode(13, OUTPUT); //set pin13 in o/p mode
}
void loop(){
while(1)
{
Serial.write("10.028371,76.328873");
Serial.write('\0');
delay(1000);
}
}
我需要一个