SW0 {label= "SW0";#gpio-cells= ;gpios= ;linux,code= ;gpio-key,wakeup;autorepeat...SW1 {label= "SW1";#gpio-cells= ;gpios= ;linux,code= ;gpio-key,wakeup;autorepeat...SW2 {label= "SW2";#gpio-cells= ;gpios= ;linux,code= ;gpio-key,wakeup;autorepeat
; pdata->num_col_gpios = ncol = of_gpio_named_count(np, “col-gpios”); of_get_property(np, “linux,no-autorepeat...pdata->no_autorepeat) __set_bit(EV_REP, input_dev->evbit); //按键的重复性时间 input_set_capability(input_dev,...pdata->num_col_gpios = ncol = of_gpio_named_count(np, “col-gpios”); … if (of_get_property(np, “linux,no-autorepeat...”, NULL)) pdata->no_autorepeat = true; if (of_get_property(np, “linux,wakeup”, NULL)) pdata->wakeup =...则每个行线的中断是独立的 unsigned int clustered_irq_flags; bool active_low; //键按下时,行线是否为低电平 bool wakeup; bool no_autorepeat
matrix_keypad(); 系统启动后,运行qt程序时,按下按键有如下打印消息 keycode is 48 unicode is 48 modifiers is 0 isPress is 1,autoRepeat...is 0 keycode is 48 unicode is 48 modifiers is 0 isPress is 0,autoRepeat is 0 发布者:全栈程序员栈长,转载请注明出处
图 1设置界面 AutoRepeat属性 获取和设置是否自动重复播放Gif动画,将该属性设置为“True”,如图 2; ?
0x07060160 /* KEY_OK */ 0x0707006c>; /* KEY_DOWN */ linux,input-no-autorepeat...keypad_data->no_autorepeat) __set_bit(EV_REP, input_dev->evbit); input_set_drvdata(input_dev, keypad_data...rows, &keypad_data->cols); if (err) return err; if (of_get_property(np, "linux,input-no-autorepeat...", NULL)) keypad_data->no_autorepeat = true; return 0; } int matrix_keypad_parse_of_params(struct
设置长按是否一直触发变化 @property(nonatomic) BOOL autorepeat; 若设置为YES,则长按值会一直改变,若设置为NO,则一次点击只会改变一次值 设置控制器的值是否循环
) Q_PROPERTY(CloudStyle cloudStyle READ getCloudStyle WRITE setCloudStyle) Q_PROPERTY(bool autoRepeat...八个角图标 QString centerText; //中间图标 CloudStyle cloudStyle; //云台样式 bool autoRepeat...void setCloudStyle(const CloudStyle &cloudStyle); //设置是否启用长按重复执行 void setAutoRepeat(bool autoRepeat...判断当前按下坐标是否在中心区域,按下则文本不同颜色 if (inCenter) { if (pressed) { position = 8; if (autoRepeat...if (contains) { if (pressed) { position = i; if (autoRepeat
clustered_irq_flags; bool active_low; //键按下时,行线是否为低电平 bool wakeup; bool no_autorepeat...ARRAY_SIZE(cols), .col_scan_delay_us = 100, .debounce_ms = 10, .active_low = 1, .no_autorepeat
= 2) { if (v->value) input_start_autorepeat(dev, v->code); else input_stop_autorepeat
设备树示例 2.1 设备树讲解 属性: 必备:compatible = "gpio-keys"; 可选: autorepeat: 表示自动重复,按下按键不松开,驱动会自动重复上报按键值 对于每一个
gpio_keys.o 设备树中增加: gpio-keys { compatible = "gpio-keys"; #address-cells = ; #size-cells = ; autorepeat
>; gpio-activelow; debounce-delay-ms = ; col-scan-delay-us = ; linux,no-autorepeat...• linux,no-autorepeat:按键按下时是否重复提交按键, 设1 就是不重复, 设0 重复。
* Command Name */ int maxargs; /* maximum number of arguments */ int repeatable; /* autorepeat
UIStepper 当前值, 在 Minimum 与 Maximum 之间; -- Step : 每次点击 + 或 -, 增加 或 减小的值; (2) Behavior 属性 Behavior 属性 : -- AutoRepeat
设置自动重复 setAutoRepeatInterval(毫秒) 设置自动重复检测间隔 setAutoRepeatDelay(毫秒) 设置初次检测延迟 autoRepeat...autoRepeatInterval() 获取自动重复检测间隔 autoRepeatDelay() 获取初次检测延迟 #查看是否自动重复 print(btn.autoRepeat
领取专属 10元无门槛券
手把手带您无忧上云