我必须配置NAT,并在连接到Linux盒的两个网关之间手动拆分internet流量。
如果每个网关都有特定的IP地址,则没有问题。我可以通过iproute2做到这一点:
ip route add default via 192.168.1.1 dev eth1
ip route add 2.3.4.5 via 192.168.0.1 dev eth0
ip route add 8.9.4.5 via 192.168.0.1 dev eth0
但我的问题太简单了!我无法更改网关地址和网络ids。我只需要使用两个来自Linux机器的地址相同的互联网网关,内核3.2.0和更高版本。
我们正在开发一个Codeigniter项目,在Linux上偶然发现了这个错误。假设你去,你会被重定向到,这会显示一个登录页面(用ion_auth写的)。这在使用Xampp的Mac和Windows上都可以正常工作,但在我的Linux Mint上运行在Lamp (没有Xampp)上就不起作用了。在我的Linux上,选项卡头和页面上只显示404未找到
Not Found
The requested URL /ci/admin/user/login/ was not found on this server.
Apache/2.4.7 (Ubuntu) Server at localhost Po
我刚开始使用bsd系统。通常,在基于linux的系统中,我会添加这样的路由:
# eth0 ip address
ip a add 10.100.1.2 dev eth0
# gw is accessible via eth0 interface
ip route add 10.100.2.1 dev eth0
# default route via 10.100.2.1
ip route add default via 10.100.2.1 dev eth0
我不明白我的openbsd命令有什么问题。它是新安装的,完全没有定制的托架。
# that's one's ok
我想更换我的linux网关盒到Mikrotik。但我从未找到如何用mikrotik的方式编写这个linux的iproute2命令:
ip route add default via 10.1.1.1 table browser
ip route add 10.1.2.0/24 via 10.1.1.2 table browser
ip rule add prio 100 from 10.1.6.2 lookup browser
有人可以引导我如何创建一个新的路由表,而不是使用主路由?
我使用以下命令将Linux盒配置为开关模式:
ip link add name switch type bridge
ifconfig switch 192.168.1.2
ip link set switch up
ip link set swp0 master switch && ip link set swp0 up
ip link set swp1 master switch && ip link set swp1 up
ip link set swp2 master switch && ip link set swp2 up
ip li
在工作中,我们有两个网络;一个WiFi网络,用于正常的互联网接入;一个内部局域网网络,用于回购等。我最近开始使用Linux,这是痛苦的,必须不断地在电缆和WiFi之间切换。在Windows上,我们通过运行以下命令来解决这个问题(这样我们就可以同时连接到两个网络):
# Add a route for all traffic to any destination starting with 10 (internal traffic):
route add 10.0.0.0 mask 255.0.0.0 10.18.21.129 metric 40 -p
# Move the default ro
我使用的是内核5.11.0,在ip路由手册1中可以读到:
Starting with Linux kernel version 3.6, there is no routing cache
for IPv4 anymore. Hence ip route show cached will never print any
entries on systems with this or newer kernel versions.
如果我键入ip route show table cache,就不会像预期的那样出现输出。
但是,当我输入:ip route get 10.0.10.44时,这是输出:
我有一个带有子链接的导航菜单。当我将鼠标放在有子链接的链接上时,当我将鼠标移到链接上时,它会闪烁。 对我的问题的说明: https://i.ibb.co/g684pXt/illustr.gif function myFunction(i) {
document.getElementById("myDropdown" + i).classList.toggle("show");
}
/* When the user clicks on the button,
toggle between hiding and showing the dropdown
我已经配置了VPN服务器。
local 192.168.0.250
dev tun
proto udp
port 1194
ca /etc/openvpn/easy-rsa/keys/ca.crt
cert /etc/openvpn/easy-rsa/keys/server-vpn.crt
key /etc/openvpn/easy-rsa/keys/server-vpn.key
dh /etc/openvpn/easy-rsa/keys/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig 10.8.0.1 10.8.0.2
push "