我有10.1.1.1和10.2.2.2绑定到eth0。
# ip address show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 04:01:05:ff:42:01 brd ff:ff:ff:ff:ff:ff
inet 10.2.2.2/24 brd 10.2.2.255 scope global eth0
inet 10.1.1.1/32 scope global eth0
我有一个基于BusyBox的嵌入式Linux系统,通过NFS安装RFS。这很好,除非我尝试使用udhcpd来获取eth0的DHCP地址。这会导致NFS挂载停止工作。对发生了什么事有什么想法吗?
/etc/网络/接口是:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
我在启动时看到的问题是:
udhcpc (v1.20.2) started
Sending discover...
Sending select for 10.140.9.57...
Lease of 10.140.9.57 obtained, leas
在我的Linux机器上,我应该如何配置我的eth1网卡来与我的ddclient一起工作?它不能使用静态ip地址,因为我的路由器不支持它,但我只能找到静态地址的配置?
我希望eth1网卡是公共地址,我的eth0是我的专用地址。我目前还没有设置eth1,但这是我的配置:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network i
我有静态IP在我的Debian系统和平由IP到互联网工作良好。不幸的是,www.google.com没有按名称进行解析。我不能在我的Linux上安装任何额外的软件,因为它不能解析名称。
/etc/网络/接口:
# Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
# /usr/share/doc/ifupdown/examples for more information.
# The loopback network interface
auto lo
iface lo inet loopback
# The
我实际上是在一个咖啡馆(类似于星芭儿,蒂姆霍顿,第二杯),在那里路由器可能受到保护。我的ip地址目前是10.0.x.x,但我希望在修改/etc/network/interfaces时获得一个静态网络( ip地址类似于192.168.x.x)。
📷
📷
如果我想得到inet 192.168.120.1,我如何修改这个文件,因为它的工作?
auto lo #automatically activates lo
iface lo inet loopback #lo with 127.0.0.1 address
auto eth0 #automa
我按照下面的指南配置了Linux Mint 17主机O/S来安装Xen
现在,在按照说明配置了网络接口之后,我重新启动了机器。我可以看到网桥通过DHCP为其分配了IP,但我无法连接到互联网。
我甚至可以成功ping通网关,但不能成功连接到任何其他地址。
我做错了什么?
这是我的/etc/network/interface文件
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet manual
auto xenbr0
iface xenbr0 inet dhcp
bridge_ports eth0
我希望我的静态路由自动加载到VPN重新连接。根据Debian上的wiki,这可以通过在/etc/network/if-pre-up.d/中放置一个脚本来完成,这就是我看到的:
#!/bin/bash
ip route add 10.8.0.0/24 dev ppp0
ip route add 192.168.0.0/24 dev ppp0
在linux启动时,这个脚本运行得很好,但是在VPN重新连接时它不会运行。为什么?
我的/etc/网络/接口文件:
auto lo eth0 eth1 asus
iface lo inet loopback
iface eth0 inet dhcp
ifac
嗨,我一直在尝试用两个Ubuntu14.04虚拟机建立一个内部网络。但到目前为止我一直不成功。它们都有具有相同网络名称的内部网络适配器,现在我需要它们在网络内部进行通信,但是ping测试没有成功。
这是我在第一个操作系统中的/etc/network/interfaces.d
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.0.100
netmask 255.255.255.0
gateway 192.168.0.254
OS #2
aut
我正在运行Debian /Linux 8服务器,用于学校作业。
在尝试重新启动服务网络时,它给了我以下错误:
root@server:~# service networking restart
[warn] Running /etc/init.d/networking restart is deprecated because it may not re-enable some interfaces ... (warning).
[....] Reconfiguring network interfaces...RTNETLINK answers: File exists
Failed to
尝试为旧Linux机器配置DNS服务。网络运行良好,ip平接入互联网。但是,如果我点名为ping,ping www.google.com命令就会挂起很长时间,并带来答案:ping: unknown host www.google.com
/etc/network/interfaces:
# Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
# /usr/share/doc/ifupdown/examples for more information.
# The loopback network interfa
这与不同,后者只要求在一个程序中工作的解决方案,并且需要源代码访问--我没有。
我有一堆产生多播通信的程序,我想在我的网络上看到,包括wifi和以太网,但我也希望它们在网络失效时不要因为“无路径”而死亡。
所以我真正想要的是把所有的多播通信从机器路由到所有可用的接口,或者如果没有接口的话回送。
在Linux上,我可以说:
sudo ifconfig lo multicast
sudo route add -net 224.0.0.0 netmask 240.0.0.0 dev lo
但这意味着使用eth0或wlan0的人无法获得多播。
同样,我可以说:
sudo ifconfig lo mul
我使用的是Ubuntu14.04,我的以太网(eth0)连接工作正常。(与DHCP)
然而,当我阅读/etc/network/interfaces时,它中没有任何关于eth0的内容。
Ubuntu14.04是否正在从其他地方读取eth0设置?
$ cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback
我想用静态地址设置我的eth0,但我不明白为什么eth0没有任何地方?
基本上,我正在尝试创建一个自定义TCP堆栈。正如您可能知道的,我不能使用eth0,因为linux内核TCP堆栈使用它,因此我需要创建一个tun/tap接口,并将它用于我的自定义TCP。
/etc/网络/接口:
auto lo
iface lo inet loopback
allow-hotplug eth0
auto eth0
iface eth0 inet static
address 192.168.1.152
netmask 255.255.255.0
broadcast 192.168.1.255
gateway 192.168.1.1
dns
在设置了iptables之后。我的out服务器有“连接超时”。我正在尝试根据我所读到的内容来设置我的iptable,这对于另一个serverFault帖子的web服务器来说是一个很好的起点。我有一个名为"iptables-setup“的文件,其内容如下:
# Allow outgoing traffic and disallow any passthroughs
iptables -P INPUT DROP
iptables -P OUTPUT ACCEPT
iptables -P FORWARD DROP
# Allow traffic already established t
我在这个问题之后的ubuntu上安装了xen。现在,当我启动ubuntu 18.04时,它需要很长时间,它在开头说:
Loading Xen 4.9-amd64 ...
WARNING: no console will be available to OS
Loading Linux 4.15.0-144-generic ...
Loading initial ramdisk ...
如何阻止Xen加载并删除它。简而言之,我如何找回我的旧操作系统,或者Xen在我的系统设置中破坏了什么?
当我安装Xen时,/etc/network/interfaces也是乱七八糟的,现在看起来如下所示:
# i
大家好,我用Linux linaro 3.1版启动了pandaboard。
一切启动正常,但以太网不工作。
我该如何解决这个问题呢?
当我启动时,这里有一些输出,这样我们就可以更好地解释这种情况。
#lsmod
no modules are enabled.
#/etc/init.d/networking eth0
device eth0 not found
failed ro bring up eth0.
#ls /sys/class/net/
there is only lo but there is no eth0.
因此,这清楚地表明以太网驱动程序没有被启用。我有没有可能克服这个问
我刚安装了一个Linux服务器。但目前我在与外界的联系上遇到了问题。我不能做wget,或ping。以下是一些相关细节:
$ping google.com
ping: unknown host google.com
cat /etc/resolv.conf
search dmust.local
nameserver 198.154.126.1
vim /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them.