我最近发现我的计算机有一个USB3条目:
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
但是遗憾的是,我只有USB2条目,所以我想找到一个是,然后用一个USB3替换它。
我在寻找Bus 002的物理位置时遇到了一些问题,我该怎么做呢?
我首先尝试在每个端口上插入一个u
我有一个64 is的USB3.0闪存驱动器,不能自动检测到。它只出现在lsusb命令的输出中。
Bus 004 Device 009: ID 1f75:0917 Innostor Technology Corporation
dmesg的输出:
usb-storage 4-2:1.0: USB Mass Storage device detected
[12196.233216] scsi host9: usb-storage 4-2:1.0
[12217.986180] usb 4-2: reset SuperSpeed USB device number 8 using
我试图通过标准的GSM USB Modem发送和接收批量SMSs,使用gnokii-SMSs在Debain上压缩6.0.3 64位。
我遵循以下站点的说明:
我已经在我的机器上安装了Postgres,所以我使用了gnokii-smsd。
shalin@developer-hp:/dev$ sudo apt-get install gnokii-smsd-pgsql
Reading package lists... Done
Building dependency tree
Reading state information... Done
gnokii-smsd-pgsql i
我最近升级到了Ubuntu 18.10 ( Cuttlefish),现在看来只有我的USB3.0端口能工作。我的主板的USB2.0端口在Windows下仍然工作得很好,dmesg显示这些端口仍然被检测到。
这里有一个diff of dmesg,在USB拇指驱动器插入非工作端口之前和之后:
> [ 5272.705639] usb 3-1: new high-speed USB device number 19 using ehci-pci
> [ 5272.833637] usb 3-1: device descriptor read/64, error -32
> [ 52
我想为OSX编写一个Ruby程序,通过USB与我的Arduino通信。为此,我将使用序列化端口gem。
我找到了一个示例代码,上面写着:
port_str = "/dev/ttyUSB0" #may be different for you
我如何扫描和找到Arduino,并知道我应该自动连接到哪个端口?(我有OSX)谢谢!
当连接任何usb卡到我的ThinkPadubuntu10.10不认识他们。我在桌面上什么都没看到。
"dmesg双尾-n10“的输出给了我:
[ 1965.696388] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1965.884537] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1966.072503] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1966.260349] hub
我正在做一个使用Arduino that (微控制器ATSAM3X8E)的项目。我的目标是能够实时跟踪我在固件中使用的一些关键变量的值。事实上,我需要绘制变量值随时间的变化图。
为了做到这一点,我决定通过本机USB端口将数据发送到我的PC上。我拥有的实时约束是,我需要在0.1ms内发送20个变量的值(每个变量有8个字节长)。在Arduino上有一个本机USB端口可用,连接到芯片的USB外围设备。我尝试通过设置UART在USB设备模式上使用UART。我只能达到115200波特的速度使用串行(UART)通信(任何较高的速度不允许适当的或我的主机PC正确发送数据)。
因此,我做了一些家务工作,发现基
我试图使用这一名为USB的老技术;)我称之为旧的,因为我在网上找到的所有教程都涉及无线打印机或IP打印机。
lpadmin的工作人员非常不清楚如何添加USB打印机,所以我来这里寻求一些帮助。
当我打印dmesg时,我可以看到我的打印机在USB上被检测到。
usb 1-1.3: new high-speed USB device number 7 using dwc_otg
usb 1-1.3: New USB device found, idVendor=03f0, idProduct=2b17
usb 1-1.3: New USB device strings: Mfr=1, Product