我在我的debian机器上使用了以下iptables脚本:
#!/bin/sh
IPT="/sbin/iptables"
# Flush old rules, old custom tables
$IPT --flush
$IPT --delete-chain
# Set default policies for all three default chains
$IPT -P INPUT DROP
$IPT -P FORWARD DROP
$IPT -P OUTPUT ACCEPT
# Enable free use of loopback interfaces
$
尝试在Ubuntu 19.10上启动PCF Dev失败,输出如下:
$ cf dev start
Downloading Resources...
Progress: |====================>| 100.0%
Setting State...
Error: argument "virbr0" is wrong: Device does not exist
Cannot find device "virbr0"
Creating the VM...
Starting the VM...
Fetching VM Address...
FA
我试图将KVM来宾(Ubuntu18.04)添加到本地网络中,就像网络中的其他实际服务器一样。我在主机系统(Ubuntu18.04)中配置了KVM桥接口,它可以很好地连接。主机系统可通过本地网络到达其他服务器。
主机系统的netplan配置:
$ cat 01-netcfg.yaml
# This file describes the network interfaces available on your system
# For more information, see netplan(5).
network:
version: 2
renderer: networkd
et
我刚刚在Arch上安装了virt-manager,我已经完成了创建VM的所有步骤,但是当我单击步骤5/5上的"Finish“时,我得到了两个弹出对话框:
无法完成安装:“请求的操作无效:网络”默认“未激活”
详细信息:
Unable to complete install: 'Requested operation is not valid: network 'default' is not active'
Traceback (most recent call last):
File "/usr/share/virt-manager/vi
我想在Debian 10主机上运行一个以Debian 9为操作系统的qemu客户机。主机连接到本地网络,我希望来宾对本地网络“可见”,就好像它是直接连接到网络的常规设备一样。为此,我通过编辑br0在主机上配置了一个名为/etc/network/interfaces的桥,如下所示:
auto lo
iface lo inet loopback
allow-hotplug eth0
auto eth0
iface eth0 inet manual
up ifconfig eth0 promisc up
down ifconfig eth0 promisc down
auto b
试图在虚拟盒上运行一个CentOS 7 VM,在我的Fedora 35机器上使用迷航器。在运行vagrant up & vagrant up --debug命令时,我得到以下消息作为输出。
There was an error talking to Libvirt. The error message is shown
below:
Call to virDomainCreateWithFlags failed: internal error: /usr/libexec/qemu-bridge-helper --use-vnet --br=virbr0 --fd=27: failed
我创建了以下配置:
/* Created a Linux bridge and brought it up */
brctl addbr AnaBr4
ifconfig AnaBr4 up
/* Created a tuntap interface and brought it up */
ip tuntap add name Xr1 mode tap
ifconfig Xr1 up
/* Added the tuntap intf to Bridge */
brctl addif AnaBr4 Xr1
我用我的一个虚拟路由器附加了Xr1。现在,我使用VMM实例化Ubuntu服务器,并将一
我在OpenStack内部运行一个KVM实例,它没有从DHCP服务器获得IP地址。
使用tcpdump,我可以在计算主机的vnet0上看到请求和答复数据包:
# tcpdump -i vnet0 -n port 67 or port 68
tcpdump: WARNING: vnet0: no IPv4 address assigned
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on vnet0, link-type EN10MB (Ethernet), captur